GB/T 5137.2
ChinaAutoRegs|GB/T 5137.2-2020 英文版/English/翻译/汽车安全玻璃试验方法第2部分:光学性能试验
Test Methods of Safety Glazing Materials Used on Road Vehicles — Part 2: Optical Properties Tests
GB/T 5137.2-2020 英文版/English/翻译
1 SCOPE
This Part of GB/T 5137 specifies the test methods of safety glazing materials used on road vehicles, i.e. luminous transmittance test, secondary image separation test, optical distortion test and luminous reflectance test.
This Part applies to testing the safety glazing materials used on road vehicles.
2 NORMATIVE REFERENCES
The following referenced documents are indispensable for the application of this document. For dated references, only the editions cited apply. For undated references, the latest editions of the normative document (including any amendments) apply.
QC/T 1119 Road vehicles-glazing materials-terminology (QC/T 1119-2019, ISO 3536: 2016, MOD)
3 TERMS AND DEFINITIONS
For the purpose of this document, the terms and definitions given in QC/T 1119 apply.
1 范围
GB/T 5137 的本部分规定了汽车用安全玻璃的可见光透射比试验、副像偏离试验、光畸变试验和可见光反射比试验的方法。
本部分适用于汽车安全玻璃的试验。
2 规范性引用文件
下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件,仅注日期的版本适用于本文件。凡是不注日期的引用文本,其最新版本(包括所有的修改单)适用于本文件。
QC/T 1119 汽车安全玻璃术语(QC/T 1119 2019,ISO 3536:2016,MOD)
3 术语和定义
QC/T 1119 界定的术语和定义适用于本文件。
4 试验条件
除特殊规定外,试验应在下述环境条件下进行:
a) 环境温度:20 ℃ ± 5 ℃;
b) 气压: 8.60 × 104 Pa~ 1.06 × 105 Pa;
c) 相对温度: 40 % ~ 80 % 。
5 可见光透射比试验
5. 1 试验目的
测定安全玻璃是否具有一定的规则透射比。
5.2 试样
应使用制品或试验片,试验片可以从制品上相应试验区域切取。试验前,试样应清洁干净,不应有污物和结露。
5.3 试验设备
5.3. 1 光源:鸽丝灯,其灯丝在1.5 mm× 1.5 mm× 3 mm 的平行六面体内,或加限定光阑。光源光谱分布应符合CIE 标准照明体A 的相对光谱功率分布。加于灯丝两端的电压应使色温为2 856 K ± 50 K,电压应稳定在± 0 .1 % 范围内。
5.3.2 光学系统:其测试原理示意图见图1 。由焦距f 不小于500 mm 并经过色差校正的两个透镜L1和L2 组成。透镜的相对口径不超过f / 20 。透镜L 1 与光源之间的距离应能调节,以便获得基本平行的光束。在离透镜L1 100 I旧n ± 50 mm 处远离光源的一侧装一光阑A1 ,把光束的直径限制在7 mm ±1 mm 内。第二个光阑儿,应放在与L1 具有相同性能的透镜L2 前,光源的成像应位于接收器的中心。第三个光阑A3, 其直径稍大于光源像最大尺寸的横断面, 应放在接收器前,以避免由试样产生的散射光落到接收器上。测量点应位于光束中心。