ChinaAutoRegs|GB/T 37336
GB/T 37336-2019 英文版/English/翻译
GB/T 37336-2019 英文版/English/翻译/汽车制动鼓
Brake Drum of Automobile
1SCOPE
This standard specifies the terms and definitions, classification, technical requirements and test methods of the brake drum for automobile.
This standard applies to the brake drums, of which the body material is grey cast iron and which is intended for the service brake of Category M and N vehicles as specified in GB/T 15089-2001.
2NORMATIVE REFERENCES
The following referenced documents are indispensable for the application of this document. For dated references, only the editions cited apply. For undated references, the latest editions of the normative document (including any amendments) apply.
GB/T 223.3Methods for chemical analysis of iron, steel and alloy - The diantipyrylmethane phosphomolybdate gravimetric method for the determination of phosphorus content
GB/T 223.58Methods for chemical analysis of iron, steel and alloy - The extraction-absorption catalytic polarographic method for the determination of manganese content
GB/T 223.59Iron, steel and alloy-Determination of phosphorus content-Bismuth phosphomolybdate blue spectrophotometric method and antimony phosphomolybdate blue spectrophotometric method
GB/T 223.60Methods for chemical analysis of iron, steel and alloy--The perchloric acid dehydration gravimetric method for the determination of silicon content
GB/T 223.62Methods for chemical analysis of iron, steel and alloy--The butyl acetate extraction photometric method for the determination of phosphorus content
GB/T 223.63Methods for chemical analysis of iron, steel and alloy--The sodium(potassium) periodate photometric method for the determination of manganese content
GB/T 228.1Metallic materials - Tensile testing - Part 1 : Method of test at room temperature
GB/T 231.1Metallic materials - Brinell hardness test - Part 1:Test method
GB/T 1031Geometrical product specifications (GPS) - Surface texture: Profile method - Surface roughness parameters and their values
GB/T 1958Geometrical Product Specifications(GPS)-Geometrical tolerance -Verification
GB/T 3177Geometrical product specifications (GPS)-Inspection of plain workpiece sizes
GB/T 7216Metallographic test for gray cast iron
GB/T 9239(All parts)Mechanical vibration - Rotor balancing
GB/T 9439-2010Grey Iron Castings
GB/T 20123Steel and iron - Determination of total carbon and sulfur content Infrared absorption method after combustion in an induction furnace (routine method)
QC/T 556Automotive Brake-Temperature measurement and thermocouple installation
3TERMS AND DEFINITIONS
For the purpose of this document, the following terms and definitions apply.
1
范围
本标准规定了汽车用制动鼓的术语和定义、分类、技术要求、检验方法。
本标准适用于 GB / T15089 — 2001 规定的 M 类和 N 类车辆行车制动器用、本体材料为灰铸铁的制动鼓。
2
规范性引 用文件
下列文件对于本文件的应用是必不可少的。 凡是注日 期的引 用文件, 仅注日 期的版本适用于本文件。 凡是不注日 期的引 用文件, 其最新版本(包括所有的修改单)适用于本文件。
GB/T 223.3 钢铁及合金化学分析方法 二安替比林甲 烷磷钼酸重量法测定磷量
GB/T 223.58 钢铁及合金化学分析方法 亚砷酸钠 - 亚硝酸钠滴定法测定锰量
GB/T 223.59 钢铁及合金 磷含量的测定 铋磷钼蓝分光光度法和锑磷钼蓝分光光度法
GB/T 223.60 钢铁及合金化学分析方法 高氯酸脱水重量法测定硅含量
GB/T 223.62 钢铁及合金化学分析方法 乙酸丁酯萃取光度法测定磷量
GB/T 223.63 钢铁及合金化学分析方法 高碘酸钠(钾)光度法测定锰量
GB/T 228.1 金属材料 拉伸试验 第1部分: 室温试验方法
GB/T 231.1 金属材料 布氏硬度试验 第1部分: 试验方法
GB/T 1031 产品几何量技术规范(GPS) 表面结构 轮廓法 表面粗糙度参数及其数值
GB/T 1958 产品几何量技术规范(GPS) 形状和位置公差 检测规定
GB/T 3177 产品几何量技术规范(GPS) 光滑工件尺寸的检验
GB/T 7216 灰铸铁金相检验
GB/T 9239 (所有部分) 机械振动 转子平衡
GB/T 9439-2010 灰铸铁件
GB/T 20123 钢铁 总碳硫含量的测定 高频感应炉燃烧后红外吸收法(常规方法)
QC/T 556 汽车制动器 温度测量和热电偶安装
3
术语和定义
下列术语和定义适用于本文件。
3.1
基准孔
mountingspigot hole
与轮毂配合的中心孔。
3.2
安装面
mountingsurface
制动鼓上与轮毂贴合的表面。
3.3
磨损极限尺寸 limiting wearsize
制动鼓摩擦面磨损后允许达到的最大径向尺寸。